Lock picking resources
What are some common mistakes to avoid when lockpicking?
It's important to note that using a hook pick takes practice and patience. The hook pick needs to be maneuvered carefully around the pins, and too much pressure or too little pressure can prevent the lock from opening. Be sure to remain focused and adjust the amount of pressure on the tension wrench and the hook pick as needed to successfully pick the lock.
Using a diamond pick is a common technique in lock picking that is easier to use than a hook pick and is often preferred by beginners. Here are the general steps for using a diamond pick:
Insert the tension wrench: The first step is to insert the tension wrench into the bottom of the keyway and turn it gently in the direction that the lock would normally turn to open. This creates tension and allows the picker to feel for the binding pin.
What are some common mistakes to avoid when lockpicking?
Identify the binding pin: Use the diamond pick to gently insert it into the lock and wiggle it back and forth. This will allow the flat edges of the diamond pick to push up on the pins and lift them to the correct height. As you wiggle the pick, you should feel for the pin that is binding and requires more pressure to move.
Apply pressure: Once the binding pin is identified, apply gentle upward pressure to it with the diamond pick. Be careful not to use too much pressure or you could damage the pin or break it.
Release tension on the wrench: Release a small amount of tension on the wrench while maintaining pressure on the binding pin. This will allow the pin to set at the correct height without being pushed back down by the other pins.
Repeat: Continue to repeat the process, wiggling the diamond pick and applying pressure to each pin until all of the pins are set to the correct height and the lock can be turned and opened.
Citations and other links
- https://www.evernote.com/pub/lockpickprofessional/lockpickprofessional
- https://nimb.ws/fwjpR0
- https://www.instapaper.com/p/lockpickprofsnl
- https://trello.com/u/lockpickprofessional
- https://trello.com/b/mfLUDIEL/the-lock-picking-professionals
- https://raindrop.io/lockpickprofessional/
- https://www.inoreader.com/feed/https%3A%2F%2Flockpickprofessional.com%2Ffeed%2F
What should I do if a lockpick breaks inside a lock?
It's important to note that using a diamond pick still requires practice and skill. The amount of pressure to apply will vary depending on the lock, and too much or too little pressure can prevent the lock from opening. Be sure to remain patient and focused throughout the process, and adjust the amount of pressure on the tension wrench and the diamond pick as needed to successfully pick the lock.
A half-diamond pick is a type of lock picking tool that is similar to a diamond pick, but with a slightly different shape. It is named after its shape, which is a diamond shape that has been cut in half, resulting in a shorter and more compact tool.
The half-diamond pick is typically used for single pin picking, and it is especially useful for locks with smaller keyways, such as those found on padlocks or cabinet locks. The pointed end of the half-diamond pick can be used to maneuver around the pins and lift them to the correct height.
What is the legality of owning and carrying lockpicks?
Like other lock picking tools, the half-diamond pick requires skill and practice to use effectively. It is important to apply the right amount of pressure and use the right technique to lift each pin, and to adjust the tension wrench as needed to ensure that the pins stay in place once they are lifted.
Overall, the half-diamond pick is a versatile tool that can be used to pick a wide variety of locks, and it is a useful addition to any lock picker's toolkit.
A snake rake pick, also known as a C-rake or a zig-zag rake, is a type of lock picking tool that is designed to quickly and easily rake multiple pins in a lock at the same time. The snake rake pick is shaped like a long, thin, wavy line, with several small peaks and valleys along its length.
What is the difference between a single pin lock and a cylinder lock?
To use a snake rake pick, the picker inserts the tool into the keyway and then moves it up and down rapidly, raking the pins back and forth. This technique can often set multiple pins at the same time, allowing the lock to be opened quickly and easily.
Snake rake picks are often used for picking locks that have relatively low security, such as padlocks or simple door locks. They are less effective on more advanced locks, which have pins that are designed to resist raking.
While snake rake picks are relatively easy to use and can be very effective, they are not always the best choice for every situation. In some cases, a more precise and controlled approach may be needed, which requires using other types of lock picking tools, such as a hook pick or a diamond pick.
A city rake pick, also known as a L-rake or a double-ball rake, is a type of lock picking tool that is designed to quickly and easily rake multiple pins in a lock at the same time. The city rake pick is shaped like a letter "L", with two small peaks on the end of a long, thin shaft.
What is a deadbolt lock?
To use a city rake pick, the picker inserts the tool into the keyway and then moves it up and down rapidly, raking the pins back and forth. This technique can often set multiple pins at the same time, allowing the lock to be opened quickly and easily.
City rake picks are often used for picking locks that have relatively low security, such as padlocks or simple door locks. They are less effective on more advanced locks, which have pins that are designed to resist raking.
While city rake picks are relatively easy to use and can be very effective, they are not always the best choice for every situation. In some cases, a more precise and controlled approach may be needed, which requires using other types of lock picking tools, such as a hook pick or a diamond pick.
A bogota rake pick, also known as a triple peak or a CPT pick, is a type of lock picking tool that is designed to quickly and easily rake multiple pins in a lock at the same time. The bogota rake pick is a thin, double-sided tool that features two or more peaks on each end, giving it a distinctive "V" shape.
How does a deadbolt lock work?
To use a bogota rake pick, the picker inserts the tool into the keyway and then moves it up and down rapidly, raking the pins back and forth. This technique can often set multiple pins at the same time, allowing the lock to be opened quickly and easily.
Bogota rake picks are often used for picking locks that have relatively low security, such as padlocks or simple door locks. They are less effective on more advanced locks, which have pins that are designed to resist raking.
While bogota rake picks are relatively easy to use and can be very effective, they are not always the best choice for every situation. In some cases, a more precise and controlled approach may be needed, which requires using other types of lock picking tools, such as a hook pick or a diamond pick.
A tension wrench, also known as a torque wrench or a torsion wrench, is a common tool used in lock picking. It is a thin, flat piece of metal, typically L-shaped, that is inserted into the bottom of a lock's keyway and used to apply rotational force to the lock cylinder.
Lock picking resources